Thermal Enhancement for Paraffinic Thermal Energy Storage by Adding Volcanic Ash

Dwi Chandra Adhitya, Dwi Rahmalina, Ismail Ismail, Muhammad Nurtanto, Hamid Abdillah

Abstract


Thermal energy storage has a good opportunity to be applied in engineering field, especially for low temperature application like automotive thermal management system. Paraffinic is a better option and considered as a good phase change material with main advantages like economically feasible, non-corrosive and safe. The main drawbacks of paraffinic system are low thermal conductivity and supercooling effect. The effort to improve the performance for paraffinic system is by g sensible material. Considering the spread of volcano in Indonesia, it can be used as sensible material for paraffinic system. The aim of the research is to examine the volcanic ash characteristic and the effect of sand addition on the paraffinic system. a standardized approach for sand examination is done and the effect of the hybrid PCM (90% paraffin and 10% volcanic ash mass ratio) are studied. The overall performance of hybrid PCM is better than pure paraffin where the vapor point of hybrid PCM is increased and there is no supercooling phenomenon observed.


Keywords


Automotive thermal management system, Paraffin, PCM, Thermal energy storage, Volcanic ash

Full Text:

PDF

References


B. Ghorbani, K. B. Mahyari, M. Mehrpooya, and M. H. Hamedi, “Introducing a hybrid renewable energy system for production of power and fresh water using parabolic trough solar collectors and LNG cold energy recovery,” Renew. Energy, vol. 148, pp. 1227–1243, 2020.

R. Ling-zhi, Z. Xin-gang, Z. Yu-zhuo, and L. Yan-bin, “The Economic Performance of Concentrated Solar Power industry in China,” J. Clean. Prod., vol. 205, no. 20 Desember 2018, pp. 799–813, 2018.

A. Peinado Gonzalo, A. Pliego Marugán, and F. P. García Márquez, “A review of the application performances of concentrated solar power systems,” Appl. Energy, vol. 255, no. March, p. 113893, 2019.

A. A. M. Junior and M. B. H. Mantelli, “Thermal performance of a novel flat thermosyphon for avionics thermal management,” Energy Convers. Manag., vol. 202, no. November, p. 112219, 2019.

A. Naidoo, “The socio-economic impacts of solar water heaters compared across two communities: A case study of Cato Manor,” Renew. Sustain. Energy Rev., vol. 119, no. November 2019, p. 109525, 2020.

A. Voirand, S. Lips, and V. Sartre, “Heat transfer and flow visualizations in a flat confined two-phase thermosyphon,” Int. J. Heat Mass Transf., vol. 148, no. xxxx, p. 119056, 2020.

T. A. Yassen, N. D. Mokhlif, and M. A. Eleiwi, “Performance investigation of an integrated solar water heater with corrugated absorber surface for domestic use,” Renew. Energy, vol. 138, no. August 2019, pp. 852–860, 2019.

H. J. Mosleh, S. J. Mamouri, M. B. Shafii, and A. H. Sima, “A new desalination system using a combination of heat pipe , evacuated tube and parabolic through collector,” ENERGY Convers. Manag., vol. 99, no. 15 July 2015, pp. 141–150, 2015.

A. Kasaeian, F. Rajaee, and W. Yan, “Osmotic Desalination by Solar Energy : A Critical Review,” Renew. Energy, vol. 134, no. April 2019, pp. 1473–1490, 2018.

S. Raja Narayanan and S. Vijay, “Desalination of water using parabolic trough collector,” Mater. Today Proc., vol. 21, no. Part 1, pp. 375–379, 2020.

J. Gao, G. Tian, A. Sorniotti, A. E. Karci, and R. Di Palo, “Review of thermal management of catalytic converters to decrease engine emissions during cold start and warm up,” Appl. Therm. Eng., vol. 147, no. 25 January 2019, pp. 177–187, 2019.

S. Wiriyasart, C. Hommalee, S. Sirikasemsuk, R. Prurapark, and P. Naphon, “Thermal management system with nanofluids for electric vehicle battery cooling modules,” Case Stud. Therm. Eng., vol. 18, no. December 2019, p. 100583, 2020.

P. Xu, C. Ji, S. Wang, X. Bai, and X. Cong, “ScienceDirect Realizing low emissions on a hydrogen-fueled spark ignition engine at the cold start period under rich combustion through ignition timing control,” Int. J. Hydrogen Energy, vol. 44, no. 16, pp. 8650–8658, 2019.

H. Lund et al., “Energy Storage and Smart Energy Systems,” Int. J. Sustain. Energy Plan. Manag., vol. 11, pp. 3–14, 2016.

A. D’Entremont, C. Corgnale, M. Sulic, B. Hardy, R. Zidan, and T. Motyka, “Modeling of a thermal energy storage system based on coupled metal hydrides (magnesium iron – sodium alanate) for concentrating solar power plants,” Int. J. Hydrogen Energy, vol. 42, no. 35, pp. 22518–22529, 2017.

A. D’Entremont, C. Corgnale, B. Hardy, and R. Zidan, “Simulation of high temperature thermal energy storage system based on coupled metal hydrides for solar driven steam power plants,” Int. J. Hydrogen Energy, vol. 43, no. 2, pp. 817–830, 2018.

D. A. Sheppard and C. E. Buckley, “The potential of metal hydrides paired with compressed hydrogen as thermal energy storage for concentrating solar power plants,” Int. J. Hydrogen Energy, vol. 44, no. 18, pp. 9143–9163, 2019.

F. Jamadi, M. Arabpour, and M. Abdolzadeh, “Performance comparison of parabolic and flat plate solar collectors utilizing in the heating system of a room-an experimental investigation,” Int. J. Renew. Energy Res., vol. 7, no. 4, pp. 1836–1849, 2017.

S. S. Mostafavi Tehrani, Y. Shoraka, K. Nithyanandam, and R. A. Taylor, “Shell-and-tube or packed bed thermal energy storage systems integrated with a concentrated solar power: A techno-economic comparison of sensible and latent heat systems,” Appl. Energy, vol. 238, no. November 2017, pp. 887–910, 2019.

S. Turrini, M. Bettonte, M. Eccher, M. Grigiante, and R. S. Brusa, “An innovative small-scale prototype plant integrating a solar dish concentrator with a molten salt storage system,” Renew. Energy, vol. 123, no. August 2018, pp. 150–161, 2018.

S. Narayanan et al., “Thermal battery for portable climate control,” Appl. Energy, vol. 149, no. 1 July 2015, pp. 104–116, 2015.

K. Manickam et al., “Future perspectives of thermal energy storage with metal hydrides,” Int. J. Hydrogen Energy, vol. 44, no. 15, pp. 7738–7745, 2019.

IRENA, Innovation Outlook: Thermal Energy Storage. Abu Dhabi: International Renewable Energy Agency, 2020.

Q. Wang, D. Zhou, Y. Chen, P. Eames, and Z. Wu, “Characterization and effects of thermal cycling on the properties of paraffin/expanded graphite composites,” Renew. Energy, vol. 147, no. March 2020, pp. 1131–1138, 2020.

H. El-Dessouky and F. Al-Juwayhel, “Effectiveness of a thermal energy storage system using phase-change materials,” Energy Convers. Manag., vol. 38, no. 6, pp. 601–617, 1997.

B. Kanimozhi, K. Harish, B. S. Tarun, P. S. Sainath Reddy, and P. S. Sujeeth, “Charging and Discharging Processes of Thermal Energy Storage System Using Phase change materials,” IOP Conf. Ser. Mater. Sci. Eng., vol. 197, no. 1, pp. 0–7, 2017.

R. Nivaskarthick, “Analysis of Thermal Energy Storage system using Paraffin Wax as Phase Change Material,” Conf. Int. Conf. Innov. Eng. Technol., vol. 1, no. 2, pp. 38–47, 2016.

I. Sarbu and C. Sebarchievici, “A comprehensive review of thermal energy storage,” Sustain., vol. 10, no. 1, pp. 1–32, 2018.

G. Hailu, P. Hayes, and M. Masteller, “Seasonal solar thermal energy sand-bed storage in a region with extended freezing periods: Part I experimental investigation,” Energies, vol. 10, no. 11, pp. 1–12, 2017.

Y. Cai, Q. Wei, F. Huang, S. Lin, F. Chen, and W. Gao, “Thermal stability , latent heat and flame retardant properties of the thermal energy storage phase change materials based on paraffin / high density polyethylene composites,” Renew. Energy, vol. 34, no. 10, pp. 2117–2123, 2009.

S. Wu, G. Fang, and X. Liu, “Dynamic discharging characteristics simulation on solar heat storage system with spherical capsules using paraffin as heat storage material,” Renew. Energy, vol. 36, no. 4, pp. 1190–1195, 2011.

A. Reyes, L. Henríquez-Vargas, J. Vásquez, N. Pailahueque, and G. Aguilar, “Analysis of a laboratory scale thermal energy accumulator using two-phases heterogeneous paraffin wax-water mixtures,” Renew. Energy, vol. 145, no. January 2020, pp. 41–51, 2020.

B. Prabhu and A. ValanArasu, “Stability analysis of TiO2–Ag nanocomposite particles dispersed paraffin wax as energy storage material for solar thermal systems,” Renew. Energy, vol. 152, no. June 2020, pp. 358–367, 2020.

H. Nikpourian, A. R. Bahramian, and M. Abdollahi, “On the thermal performance of a novel PCM nanocapsule: The effect of core/shell,” Renew. Energy, vol. 151, no. May 2020, pp. 322–331, 2020.

X. Zuo, J. Li, X. Zhao, H. Yang, and D. Chen, “Emerging paraf fi n / carbon-coated nanoscroll composite phase change material for thermal energy storage,” Renew. Energy, vol. 152, no. June 2020, pp. 579–589, 2020.

N. Ahmed, K. E. Elfeky, L. Lu, and Q. W. Wang, “Thermal performance analysis of thermocline combined sensible-latent heat storage system using cascaded-layered PCM designs for medium temperature applications,” Renew. Energy, vol. 152, no. June 2020, pp. 684–697, 2020.

Q. A. Jawad, A. M. J. Mahdy, A. H. Khuder, and M. T. Chaichan, “Improve the performance of a solar air heater by adding aluminum chip, paraffin wax, and nano-SiC,” Case Stud. Therm. Eng., vol. 19, no. March 2020, p. 100622, 2020.

R. Elbahjaoui and H. El Qarnia, “Performance evaluation of a solar thermal energy storage system using nanoparticle-enhanced phase change material,” Int. J. Hydrogen Energy, vol. 44, no. 3, pp. 2013–2028, 2019.

N. Mahfoudi, A. Moummi, and M. El Ganaoui, “Sand as a heat storage media for a solar application: Simulation results,” Appl. Mech. Mater., vol. 621, no. August 2014, pp. 214–220, 2014.

B. Sivapalan, M. Neelesh Chandran, S. Manikandan, M. K. Saranprabhu, S. Pavithra, and K. S. Rajan, “Paraffin wax–water nanoemulsion: A superior thermal energy storage medium providing higher rate of thermal energy storage per unit heat exchanger volume than water and paraffin wax,” Energy Convers. Manag., vol. 162, no. February, pp. 109–117, 2018.

P. Zhang, Z. N. Meng, H. Zhu, Y. L. Wang, and S. P. Peng, “Melting heat transfer characteristics of a composite phase change material fabricated by paraffin and metal foam,” Appl. Energy, vol. 185, no. 1 January 2017, pp. 1971–1983, 2017.

A. Frazzica, M. Manzan, A. Sapienza, A. Freni, G. Toniato, and G. Restuccia, “Experimental testing of a hybrid sensible-latent heat storage system for domestic hot water applications,” Appl. Energy, vol. 183, no. 1 December 2016, pp. 1157–1167, 2016.

A. Palacios, M. Elena Navarro, C. Barreneche, and Y. Ding, “Hybrid 3 in 1 thermal energy storage system – Outlook for a novel storage strategy,” Appl. Energy, vol. 274, no. April, p. 115024, 2020.

S. Drissi, T. Ling, and K. Hung, “Thermochimica Acta Thermal efficiency and durability performances of paraffinic phase change materials with enhanced thermal conductivity – A review,” Thermochim. Acta, vol. 673, no. August 2018, pp. 198–210, 2019.

M. Diago, A. C. Iniesta, A. Soum-Glaude, and N. Calvet, “Characterization of desert sand to be used as a high-temperature thermal energy storage medium in particle solar receiver technology,” Appl. Energy, vol. 216, no. October 2017, pp. 402–413, 2018.

P. Dumka, A. Sharma, Y. Kushwah, A. S. Raghav, and D. R. Mishra, “Performance evaluation of single slope solar still augmented with sand-filled cotton bags,” J. Energy Storage, vol. 25, no. August, p. 100888, 2019.

G. Hailu, P. Hayes, and M. Masteller, “Long-term monitoring of sensible thermal storage in an extremely cold region,” Energies, vol. 12, no. 9, pp. 1–19, 2019.

R. Gulfam, P. Zhang, and Z. Meng, “Advanced thermal systems driven by paraffin-based phase change materials – A review,” Appl. Energy, vol. 238, no. June 2018, pp. 582–611, 2019.

A. S. for T. and Materials, Standard Practice for Measuring Elements in Water by Flame Atomic Absorption Spectrophotometry, Vol. Sec.,. ASTM, 2010.

A. S. for T. and Materials, Standard Test Methods for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method. ASTM, 1999.

American Society for Testing and Materials, Measuring and Recording Water Quality Parameters for Monitoring Purposes. ASTM, 2014.

N. Ukrainczyk, S. Kurajica, and J. Šipušić, “Thermophysical comparison of five commercial paraffin waxes as latent heat storage materials,” Chem. Biochem. Eng. Q., vol. 24, no. 2, pp. 129–137, 2010.

Lutiyatmi, T. Daryanto, and H. Abdillah, “PENERAPAN FACE SAND PADA PASIR CETAK UNTUK MENGURANGI REJECT PRODUK DI PT. MITRA KARYA UTAMA (IMPLEMENTATION OF FACE SAND ON SAND MOLD TO REDUCE PRODUCT REJECT IN PT. MITRA KARYA UTAMA),” J. Berdaya Mandiri, vol. 3, no. 1, pp. 518–528, 2021.

S. I. Khasanah, N. R. Sesunan, and H. Abdillah, “Study of the reclamation of waste co2 moulding sand in foundry industry,” Int. J. Emerg. Trends Eng. Res., vol. 8, no. 9, pp. 5454–5459, 2020.




DOI: http://dx.doi.org/10.30870/vanos.v6i1.10990

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.