Improving press machine efficiency using a TPM approach and Six Big Losses analysis

Supriyati Supriyati, Tri Ngudi Wiyatno

Abstract


This study aims to improve the efficiency of press machines in the food manufacturing industry by implementing the Total Productive Maintenance (TPM) method and analyzing the Six Big Losses. The main issues identified include high downtime, excessive vibrations, and machine component failures, all of which negatively impact production efficiency. This research measures Overall Equipment Effectiveness (OEE) based on three key parameters: availability, performance, and quality. The results indicate that the average OEE is 84%, which falls below the 85% standard recommended by the Japan Institute of Plant Maintenance (JIPM). The primary causes of low efficiency are idling and minor stoppages (48%) and equipment failures (28%), both of which are influenced by a lack of preventive maintenance and errors in machine settings. A fishbone diagram analysis identifies the key factors contributing to inefficiency. To enhance machine effectiveness and reduce waste, a more optimized TPM implementation is recommended, focusing on Autonomous Maintenance and Preventive Maintenance. This study confirms that applying TPM and OEE can optimize production performance and improve the competitiveness of the manufacturing industry through enhanced maintenance systems and machine efficiency.

Keywords


OEE; Six Big Losses; TPM; Availability; Performance; Quality Ratio

Full Text:

PDF

References


R. Thorat and G. T. Mahesha, “Improvement in productivity through TPM Implementation,” Mater. Today Proc., vol. 24, pp. 1508–1517, 2020, doi: 10.1016/j.matpr.2020.04.470.

M. F. Ahmad, S. F. Zamri, Y. Ngadiman, S. W. Chan, N. Zakuan, A. H. Nor Aziati, dan Y. Baba, “The impact of Total Productive Maintenance (TPM) as mediator between Total Quality Management (TQM) and business performance,” International Journal of Supply Chain Management, vol. 8, no. 1, pp. 1033-1042, 2019.

V. Shankul dan Y. Buke, “Relationship of 5S, TPM and SMS to enhance safety performance of manufacturing industry,” Journal of Industrial Safety Engineering, vol. 6, no. 2, pp. 1-13, 2019.

I. Leksic, N. Stefanic, dan I. Veza, “The impact of using different lean manufacturing tools on waste reduction,” Advances in Production Engineering & Management, vol. 15, no. 1, pp. 81-92, 2020, doi: 10.14743/apem2020.1.351.

S. L. Fuadiya and E. P. Widjajati, “Analysis of sag mill machine performance using overall equipment effectiveness and failure model and effects analysis method,” Int. J. Ind. Optim., vol. 3, no. 2, pp. 141–153, 2022, doi: 10.12928/ijio.v3i2.6701.

J. Biswas, “Total Productive Maintenance: An In-depth Review with a Focus on Overall Equipment Effectiveness Measurement,” Int. J. Res. Ind. Eng., vol. 13, no. 4, pp. 376–383, 2024, doi: 10.22105/riej.2024.453380.1436.

D. N. Gandhi and V. Deshpande, “a Review of Tpm To Implement Oee Technique in Manufacturing Industry,” Ind. Eng. J., vol. 11, no. 6, 2018, doi: 10.26488/iej.11.6.1073.

R. H. Pratama, A. S. Pratama, dan D. Sari, “Implementation of overall equipment effectiveness (OEE) in improving production efficiency: a case study in manufacturing industry,” IOP Conference Series: Materials Science and Engineering, vol. 1096, no. 1, pp. 012069, 2021, doi: 10.1088/1757-899X/1096/1/012069.

S. Dewi, J. Alhilman, and F. T. D. Atmaji, “Evaluation of Effectiveness and Cost of Machine Losses using Overall Equipment Effectiveness (OEE) and Overall Equipment Cost Loss (OECL) Methods, a case study on Toshiba CNC Machine,” IOP Conf. Ser. Mater. Sci. Eng., vol. 847, no. 1, 2020, doi: 10.1088/1757-899X/847/1/012020.

M. A. Musa, N. I. Kasim, A. R. Razali, Mahadzir, and W. A. N. Wan Saidin, “Improvement of Overall Equipment Effectiveness (OEE) through Implementation of Autonomous Maintenance in Crankcase Line,” Appl. Mech. Mater., vol. 761, pp. 165–169, May 2015, doi: 10.4028/www.scientific.net/AMM.761.165.

I. A. Mahmoud, M. Fahmyaly, A. Mohib, and I. H. Afefy, “Integration of benchmarking with overall Equipment Cost Loss for industrial process improvement,” Jordan J. Mech. Ind. Eng., vol. 13, no. 1, pp. 49–59, 2019.

R. F. Prabowo, H. Hariyono, and E. Rimawan, “Total Productive Maintenance (TPM) pada Perawatan Mesin Grinding Menggunakan Metode Overall Equipment Effectiveness (OEE),” J. Ind. Serv., vol. 5, no. 2, 2020, doi: 10.36055/jiss.v5i2.8001.

A. Sutoni, W. Setyawan, and T. Munandar, “Total Productive Maintenance (TPM) Analysis on Lathe Machines using the Overall Equipment Effectiveness Method and Six Big Losses,” J. Phys. Conf. Ser., vol. 1179, no. 1, p. 012089, Jul. 2019, doi: 10.1088/1742-6596/1179/1/012089.

R. Sharma, “Overall equipment effectiveness measurement of TPM manager model machines in flexible manufacturing environment : a case study of automobile sector Richa Sharma,” Int. J. Product. Qual. Manag., vol. 26, no. 2, pp. 206–222, 2019.

M. Sayuti, Juliananda, Syarifuddin, and Fatimah, “Analysis of the Overall Equipment Effectiveness (OEE) to Minimize Six Big Losses of Pulp machine: A Case Study in Pulp and Paper Industries,” IOP Conf. Ser. Mater. Sci. Eng., vol. 536, no. 1, 2019, doi: 10.1088/1757-899X/536/1/012136.

I. S. Muthalib, M. Rusman, and G. L. Griseldis, “Overall Equipment Effectiveness (OEE) analysis and Failure Mode and Effect Analysis (FMEA) on Packer Machines for minimizing the Six Big Losses-A cement industry case,” IOP Conf. Ser. Mater. Sci. Eng., vol. 885, no. 1, 2020, doi: 10.1088/1757-899X/885/1/012061.

Z. T. Xiang and C. J. Feng, “Implementing total productive maintenance in a manufacturing small or medium-sized enterprise,” J. Ind. Eng. Manag., vol. 14, no. 2, pp. 152–175, 2021, doi: 10.3926/jiem.3286.

L. Hassani, “Ladan Hassani the impact of Overall Equipment Effectiveness on production losses in Moghan Cable & Wire,” vol. 9, no. 4, pp. 565–576, 2004.

E. Y. T. Adesta, H. A. Prabowo, and D. Agusman, “Evaluating 8 pillars of Total Productive Maintenance (TPM) implementation and their contribution to manufacturing performance,” IOP Conf. Ser. Mater. Sci. Eng., vol. 290, no. 1, 2018, doi: 10.1088/1757-899X/290/1/012024.

M. D. O. dos Reis, R. Godina, C. Pimentel, F. J. G. Silva, and J. C. O. Matias, “A TPM strategy implementation in an automotive production line through loss reduction,” Procedia Manuf., vol. 38, no. 2019, pp. 908–915, 2019, doi: 10.1016/j.promfg.2020.01.173.

I. M. Ribeiro, R. Godina, C. Pimentel, F. J. G. Silva, and J. C. O. Matias, “Implementing TPM supported by 5S to improve the availability of an automotive production line,” Procedia Manuf., vol. 38, no. 2019, pp. 1574–1581, 2019, doi: 10.1016/j.promfg.2020.01.128.

E. Gidey, B. Beshah, and D. Kitaw, “Review on the evolving relationship between quality and productivity,” Int. J. Qual. Res., vol. 8, no. 1, pp. 47–60, 2014.

E. E. Blanco, E. N. F. Solano, dan G. G. Moreno, “Implementation of the autonomous maintenance pillar based on the TPM philosophy,” DYNA (Colombia), vol. 87, no. 212, pp. 74-81, 2020, doi: 10.15446/dyna.v87n212.83211.

R. CG, R. MJ, and Y. Krishna, “A Case Study to Determine OEE-A KPI Representing the Overall Productivity of a Machine.,” J. Mines, Met. Fuels, vol. 71, no. 3, pp. 359–366, 2023, doi: 10.18311/jmmf/2023/33720.

N. Gwangwava, G. A. Baile, P. Dikgale, and K. Kefhilwe, “Framework for Total Productive Maintenance for an Sme,” J. Eng. Technol. Ind. Appl., vol. 7, no. 29, pp. 52–61, 2021, doi: 10.5935/jetia.v7i29.740.

S. Sahoo and S. Yadav, “Influences of TPM and TQM Practices on Performance of Engineering Product and Component Manufacturers,” Procedia Manuf., vol. 43, pp. 728–735, 2020, doi: 10.1016/j.promfg.2020.02.111.

A. Singh and I. S. Ahuja, “Review of 5S methodology and its contributions towards manufacturing performance,” Int. J. Process Manag. Benchmarking, vol. 5, no. 4, p. 408, 2015, doi: 10.1504/IJPMB.2015.072320.

M. Dieste, R. Panizzolo, and J. A. Garza-Reyes, “Evaluating the impact of lean practices on environmental performance: evidence from five manufacturing companies,” Prod. Plan. Control, vol. 31, no. 9, pp. 739–756, Jul. 2020, doi: 10.1080/09537287.2019.1681535.

Pinto G., Silva F.J.G., Fernandes N.O., Casais R., Baptista A., and Carvalho C., “Implementing a maintenance strategic plan using TPM methodology,” Int. J. Ind. Eng. Manag., vol. 11, no. 3, pp. 192–204, 2020, [Online].

F. Gunawan, A. Setiawan, dan H. Humaedi, “Pengukuran nilai efektivitas mesin reaktor A700,” Jurnal Teknik Mesin Untirta, vol. 4, no. 1, pp. 2-9, 2018.

E. Febianti, K. D. Safitri, K. Kulsum, B. Kurniawan, P. F. Ferdinant, and H. Setiawan, “Measurement of effectiveness of food processing machine through overall equipment effectiveness (OEE),” J. Ind. Serv., vol. 8, no. 1, p. 46, 2022, doi: 10.36055/jiss.v8i1.14076.

I. K. Wardani, F. T. Dwi Atmaji, and J. Alhilman, “Pengukuran dan analisa efektivitas mesin pencetak paving menggunakan metode overall equipment effectiveness (OEE),” J. Ind. Serv., vol. 7, no. 1, p. 125, 2021, doi: 10.36055/jiss.v7i1.12336.

I. Leksic, N. Stefanic, and I. Veza, “The impact of using different lean manufacturing tools on waste reduction,” Adv. Prod. Eng. Manag., vol. 15, no. 1, pp. 81–92, 2020, doi: 10.14743/APEM2020.1.351.

Supriyati, Wiyatno Tri Ngudi, and Darmawan Heru, “Peningkatan produksi plastik injection dengan analisis Overall Equipment Effectiveness dan Single Minute Exchange of Dies (Increase of plastic injection production using Overall Equipment Effectiveness and Single Minute Exchange of Dies Analysis),” Oper. Excell. J. Appl. Ind. Eng., vol. 2021, no. 3, pp. 394–406, 2021.




DOI: http://dx.doi.org/10.62870/jiss.v10i2.28344

Refbacks

  • There are currently no refbacks.


  is supported by