PENGARUH ARUS DAN JARAK KAMPUH PENGELASAN TERHADAP DISTORSI SAMBUNGAN PELAT BAJA KARBON RENDAH DENGAN MENGGUNAKAN SMAW

Amir Arifin, M Hendrianto

Abstract


Proses pengelasan sambungan pelat baja karbon rendah menggunakan SMAW menggunakan kampuh V dengan variasi arus dan jarak sering muncul distorsi pada hasil pengelasan. Penelitian ini bertujuan untuk menginvestigasi pengaruh arus dan jarak kampuh pengelasan terhadap distorsi, yang terjadi pada hasil las. Pada penelitian ini digunakan tebal pelat  6 mm dan arus pengelasan (50, 7 , 100 dan 125 A) serta jarak kampuh (2,3,4 dan 5 mm). Pengukuruan distorsi dengan menggunakan dial indicator. Hasil pengujian menunjukkan bahwa terdapat hubungan linear antara peningkatan arus dan pertambahan jarak kampuh terhadap distorsi yang dihasilkan. Selain itu pengujian kekerasan menunjukkan bahwa kekerasan relative lebih rendah pada pengelasan yang menggunakan arus 50 A

Keywords


Pengelasan SMAW Kampuh V, Sudut Distorsi

Full Text:

PDF

References


Akella, S., Kumar, B. R., & Krishnaiah, Y. (2013). Optimisation of welding process parameters for distortion control with Taguchi approach. International Journal of Precision Technology, 3(2), 206. doi: 10.1504/ijptech.2013.053305

Callister, W. D., & Rethwisch, D. G. (2013). Materials Science and Engineering: An Introduction, 9th Edition: Ninth Edition: John Wiley and Sons, Incorporated.

Guo, N., Yin, X. Q., Liang, J., & Ma, N. (2016). Effects of heat input on welding buckling distortion by experimental measurement method. Science and Technology of Welding and Joining, 22(5), 381-388. doi: 10.1080/13621718.2016.1251079

Jeffus, L. (2016). Welding: Principles and Applications: Cengage Learning.

Karadeniz, E., Ozsarac, U., & Yildiz, C. (2007). The effect of process parameters on penetration in gas metal arc welding processes. Materials & Design, 28(2), 649-656. doi: 10.1016/j.matdes.2005.07.014

Kchaou, Y., Haddar, N., Hénaff, G., Pelosin, V., & Elleuch, K. (2014). Microstructural, compositional and mechanical investigation of Shielded Metal Arc Welding (SMAW) welded superaustenitic UNS N08028 (Alloy 28) stainless steel. Materials & Design, 63, 278-285. doi: 10.1016/j.matdes.2014.06.014

Kozak, J., & Kowalski, J. (2015). The Influence of Manufacturing Oversizing on Post-Welding Distortions of The Fillet Welded Joint. Polish Maritime Research, 22, 59-63.

Papazoglou, V. J., & Masubuchi, K. (1978). Analysis and Control of Distortion in Welded Aluminum Structures. Welding Research, September, 251-262.

Vashishtha, H., Taiwade, R. V., Sharma, S., & Patil, A. P. (2017). Effect of welding processes on microstructural and mechanical properties of dissimilar weldments between conventional austenitic and high nitrogen austenitic stainless steels. Journal of Manufacturing Processes, 25, 49-59. doi: 10.1016/j.jmapro.2016.10.008

Wiryosumarto, H., & Okumura, T. (2010). Teknologi Pengelasan Logam: Pradnya Paramita.




DOI: http://dx.doi.org/10.36055/fwl.v1i1.3288

Refbacks

  • There are currently no refbacks.


Creative Commons License
FLYWHEEL: JURNAL TEKNIK MESIN UNTIRTA is licensed under a Creative Commons Attribution 4.0 International License.