STUDY OF PARTICLE BOARDS CHARACTERISTIC BASED ON SENGON WOOD PARTICLE AND OIL PALM EMPTY FRUIT BUNCHES

Sunardi Sunardi, Rizky Kurnia Putra, Rina Lusiani, Iman Saefuloh, Agung Sudrajad

Abstract


Oil palm empty fruit bunches (OPEFB) as a by-product of the palm oil processing industry. This waste can cause problems for the environment and human health. Utilization of OPEFB waste as particle board material to reduce this waste. The composition of the particle board is based on volume fraction, namely 15% empty palm fruit fiber, 15% epoxy resin, 20% PVAc adessive, and 50% sawdust. The manufacturing process of samples was carried out using the single punch cold press method with compaction pressure of 10, 30, and 50 bar. The experimental results show that a compacting pressure of 10 bar can produce particle board performance according to SNI 03-2105-2006 with a characteristic density of 0.93 gram/cm3, thickness swelling of 2.52%, hardness of 24 N/mm2, flexural strength of 840.05 N/mm2, and impact strength 6.00 kJ/m2.

Full Text:

PDF

References


R. Lusiani, S. Sunardi and Y. Ardiansah, "Utilization of empty palm oil fruit bunches as composite particle boards with variations in fiber length," Flywheel: Journal of Mechanical Engineering Untirta, vol. 1, no. 1, pp. 46-54, 2015.

B. Raharjo, "Utilization of empty palm oil fruit bunches as an alternative to particle board," Indonesian Journal of Laboratory, vol. 2, no. 2, pp. 1-9, 2020.

S. Sunardi, R. Lusiani, J. Andrean and M. Fawaid, "Characteristics and potential of palm oil waste as particle board," in the National Seminar on Environmental Management SNPL 2017 , Palembang, 2017.

D. Fithriani, T. Nugroho and J. Basmal, "The effect of pressing time on the characteristics of particle board from solid waste processing Gracilaria sp," Journal of Postharvest and Marine and Fisheries Biotechnology, vol. 1, no. 2, pp. 125-133, 2006.

RS Mbakop, G. Lebrun and F. Brouillette, “Effect of compaction parameters on preform permeability and mechanical properties of unidirectional flax fiber composites,” Composite Part B, vol. 176, pp. 1-10, 2019.

SF Gharaibeh, WM Obeidat and N. Al-Zoubi, “Effect of post-compaction heating on characteristics of microcrystalline cellulose compacts,” e-Polymers, vol. 22, p. 536–543, 2022.

L. Xiao, Y. Sun dan L. Yu, “The effect of compaction parameters and dielectric composition on the properties of soft magnetic composites,” Journal of Physics: Conference Series, vol. 303, pp. 1-6, 2011.

M. Viel, F. Collet and C. Lanos, “Effect of compaction on multi-physical properties of hemp-black liquor composites,” Journal of Material Research and Technology, vol. 9, no. 2, pp. 2487-2494, 2020.

M. Dixit and R. Srivastava, “Effect of compaction pressure on microstructure, density and hardness of Copper prepared by Powder Metallurgy route,” IOP Conf. Series: Materials Science and Engineering, vol. 377, pp. 1-9, 2018.

Asfarizal, A. Kasim, Gunawarman and Santosa, "Effects of Pressure and Temperature on the Production of Particle Boards Made from Empty Palm Oil Bunches and Pine Bark," Journal of Mechanical Engineering, Padang Institute of Technology, vol. 9, no. 1, pp. 1-5, 2019.




DOI: http://dx.doi.org/10.62870/timer.v1i1.20477

Refbacks

  • There are currently no refbacks.


This work is licensed under Creative Commons Attribution 4.0 International