Design and Build of Electric Car Frame SULA Evolution

Adhan Efendi, Abu Rizal Fahmi

Abstract


This research is research and development. The purpose of this research is to make an electric car design drawing according to the national electric car race standards that have better dimensions and turbulence than the previous design. The method in designing an electric car frame is by observing and studying the literature. The results of data collection are selected and reviewed and a design is made according to standards. Supervise and evaluate so that design and manufacture are not much different. The results obtained in the design are (1) The design results in the manufacture of the Sula evolution electric car frame, there are two parts, namely the mainframe and the suspension frame. The frame is divided into several parts, namely the seat holder, battery holder, controller holder, and rollbar. While the suspension frame is the front arm and rear arm; (2) In the design of the Sula evolution electric car frame, the calculations carried out are using the Autodesk Inventor application and the formula in analyzing the results of the mainframe design for the Sula Evolution electric car, namely the calculation of the weight of the material based on the data taken from the design drawings made.

Keywords


Design, Electric Car, Frame

Full Text:

PDF

References


M. F. Adhan Efendi, “ELECTRIC SYSTEMS IN SULA ELECTRIC CARS IN SULA ELECTRIC CARS’ SUBANG STATE POLYTECHNIC,” J. Mech. Eng. Educ., vol. 5, no. 1, pp. 47-58., 2020, doi: http://dx.doi.org/10.30870/vanos.v5i1.7352.

A. Khumaedi, N. Soedjarwanto, and A. Trisanto, “Otomatisasi Pengereman Motor DC Secara Elektris Sebagai Referensi Sistem Keamanan Mobil Listrik,” J. Rekayasa dan Teknol. Elektro, vol. 8, no. 1, pp. 31–36, 2014, doi: https://doi.org/10.23960/elc.v8n1.121.

C. O. Quandt, “Manufacturing the electric vehicle: a window of technological opportunity for southern California,” Environ. Plan. A, vol. 27, no. 6, pp. 835–862, 1995, doi: 10.1068/a270835.

A. Guizani, M. Hammadi, J. Y. Choley, T. Soriano, M. S. Abbes, and M. Haddar, “Electric vehicle design, modelling and optimization,” Mech. Ind., vol. 17, no. 4, 2016, doi: 10.1051/meca/2015095.

A. S. B. Adhan Efendi, “Pemeliharaan Mesin Mobil Listrik Sula Politeknik Negeri Subang,” J. Rekayasa Mesin, vol. 14, no. 3, p. 79, 2019, doi: 10.32497/jrm.v14i3.1591.

M. Adriana, A. A. B.P, and M. Masrianor, “Rancang Bangun Rangka (Chasis) Mobil Listrik Roda Tiga Kapasitas Satu Orang,” J. Elem., vol. 4, no. 2, p. 129, 2017, doi: 10.34128/je.v4i2.64.

A. D. Novfowan, “Mobil Listrik Tantangan Masa Depan,” Majalah Bistek Edisi 06, Jakarta, 1998.

C. O. Quandt, “Manufacturing the electric vehicle: a window of technological opportunity for southern California,” Environ. Plan. A, vol. 27, no. 6, pp. 835–862, 1995, doi: 10.1068/a270835.

L. Setiono, “PERANCANGAN MEKANIKA DAN REALISASI KONTROL MOBIL LISTRIK,” e-Proceeding Eng., vol. 3, no. 3, pp. 4669–4675, 2016.

E. Helmers and P. Marx, “Electric cars: Technical characteristics and environmental impacts,” Environ. Sci. Eur., vol. 24, no. 4, 2012, doi: 10.1186/2190-4715-24-14.

F. Un-Noor, S. Padmanaban, L. Mihet-Popa, M. N. Mollah, and E. Hossain, “A comprehensive study of key electric vehicle (EV) components, technologies, challenges, impacts, and future direction of development,” Energies, vol. 10, no. 8, 2017, doi: 10.3390/en10081217.

Z. S. Gelmanova et al., “Electric cars. Advantages and disadvantages,” J. Phys. Conf. Ser., vol. 1015, no. 5, 2018, doi: 10.1088/1742-6596/1015/5/052029.

A. F. and L. S. C. Mahmoudi, “An overview of electric Vehicle concept and power management strategies,” Int. Conf. Electr. Sci. Technol. Maghreb, vol. 1, no. 8, 2014, doi: 10.1109/CISTEM.2014.7077026.

D. Carley, The Beginners Guide to Electric Vehicles ( EV ), no. August. 2014.

C. Iclodean, B. Varga, N. Burnete, D. Cimerdean, and B. Jurchiş, “Comparison of Different Battery Types for Electric Vehicles,” IOP Conf. Ser. Mater. Sci. Eng., vol. 252, no. 1, 2017, doi: 10.1088/1757-899X/252/1/012058.

B. Kampman et al., Green Power for Electric Cars- Development of policy recommendations to harvest the potential of electric vehicles, no. January. 2010.

A. Guizani, M. Hammadi, J. Y. Choley, T. Soriano, M. S. Abbes, and M. Haddar, “Electric vehicle design, modelling and optimization,” Mech. Ind., vol. 17, no. 4, 2016, doi: 10.1051/meca/2015095.

M. Burridge and S. Alahakoon, “The Design and Construction of a Battery Electric Vehicle Propulsion System - High Performance Electric Kart Application,” IOP Conf. Ser. Earth Environ. Sci., vol. 73, no. 1, 2017, doi: 10.1088/1755-1315/73/1/012016.

J. Santiago, J. G. Oliveira, J. Lundin, J. Abrahamsson, A. Larsson, and H. Bernhoff, “Design parameters calculation of a novel driveline for electric vehicles,” World Electr. Veh. J. Vol., vol. 3, p. 0225, 2009.

M. S. B. A. Razak, M. H. Bin Hasim, and N. A. Bin Ngatiman, “Design of Electric Vehicle Racing Car Chassis using Topology Optimization Method,” MATEC Web Conf., vol. 97, no. January, 2017, doi: 10.1051/matecconf/20179701117.




DOI: http://dx.doi.org/10.30870/vanos.v6i1.9436

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.