Experimental Study of Joint Tool Variations in Cold Rolled Steel Structure Connection Systems C75 – 0,65 mm

Hendrian Budi Bagus Kuncoro; Andi Indianto; Mukhlisya Dewi Ratna Putri

doi:10.36055/fondasi.v13i2.28646

Experimental Study of Joint Tool Variations in Cold Rolled Steel Structure Connection Systems C75 – 0,65 mm

Hendrian Budi Bagus Kuncoro, Andi Indianto, Mukhlisya Dewi Ratna Putri

Abstract

C75 cold rolled steel is a material used in building construction with a lighter weight compared to conventional steel. One important aspect in the design of C75 light steel is the connection, where the connection must be designed safely so it is very important to maintain the structural integrity of the building and ensure the safety of building users. The aim of the research is to obtain the correct formulation for the C75 mild steel connection type in relation to the thickness of the C75 cold rolled steel. The method used is to create a connection system in the form of a variety of connections consisting of connections using screws only, combined screws and bolts, and connections using rivet nails. Overall, from the test results, it was found that the use of mild steel connections with a modified model between screws and bolts produced a greater value compared to using rivet connection tools alone or screws alone, this happened the same for every thickness of mild steel tested, both thickness 0, 65 mm, 0.75 mm or 1.00 mm. The greatest results were found in the connection of 4 screws and 1 bolt at a mild steel thickness of 1.00 to 100.00 N with a deflection of 2.58 mm. When compared with rivets, the increase reached 42.50%, while compared with screws, there was an increase of 20.00%. So rivet connections are brittle compared to screws and screw and bolt connections are a more ductile connection, so they can be recommended as connections in light steel. It's just that mild steel which has a greater thickness tends not to cause buckling compared to mild steel which is much thinner, where buckling is likely to occur in the mild steel material.

Keywords

C75 cold rolled steel, screws, bolts, rivets nails

Full Text:

PDF

References

Apriani, Widya, Fadrizal Lubis, and Muthia Anggraini. “Analisis Sambungan Sekrup pada Konstruksi Rangka Atap Baja ringan Menurut SNI 7971: 2013.” SIKLUS: Jurnal Teknik Sipil 3, no. 2 (2017): 49-57.

Budiono, Agus, and AA Gede Sutapa. “Perilaku Kegagalan Sambungan Batang Tarik Pada Struktur Baja Ringan Dengan Variasi Konfigurasi Sekrup.”, vol. 4 no.6, 1-8, 2015

Devtrina, Fahmi Savero, and Y. Djoko Setiyarto. “STUDI EKSPERIMENTAL PENGGUNAAN SEKRUP TIPE SELF DRILLING SCREW PADA SAMBUNGAN BAJA RINGAN (COLD FORMED STEEL).” CRANE: Civil Engineering Research Journal 1, no. 1 (2020).

Duppa, Hakim. "Efektivitas Penggunaan Baja Ringan Untuk Struktur Rangka Atap Gedung." (2018).

Fitrah, Ridho Aidil, and R. Nofriyandi. “Desain Sambungan Baut Rangka Atap Baja Ringan Bentang Panjang Tipe Parallel Chord.” Rang Teknik Journal 3, no. 1 (2020): 99-103.

Haris, Sabril, and Hazmal Herman. “Studi Eksperimental Perilaku Sambungan Dengan Alat Sambung Sekrup Pada Elemen Struktur Baja Ringan.” In Proceedings ACES (Annual Civil Engineering Seminar), vol. 1, pp. 390-396. 2016.

Hasrianto, Hasrianto, Awal Syahrani Sirajuddin, Mustafa Mustafa, and Kristian Selleng. “ANALISIS SAMBUNGAN BATANG TARIK PADA STRUKTUR BAJA RINGAN DENGAN VARIASI KONFIGURASI SEKRUP.” Jurnal MEKANIKAL 10, no. 1.

Ikhsan, Muhammad Nur, Ali Awaludin, and Andreas Triwiyono. “Kuat Tarik dan Pola Kegagalan Kombinasi Sambungan Baut dan Sekrup pada Baja Canai Dingin.” Inersia: Jurnal Teknik Sipil dan Arsitektur 16, no. 2 (2020): 144-157.

Indarto, Richo Oktavian, and Budi Suswanto. “Studi Analisis Perilaku Jembatan Pejalan Kaki Dengan Sambungan Sekrup Dan Adhesive Pada Cold-Formed Steel.” Jurnal Aplikasi Teknik Sipil 18, no. 1 (2020): 73-80.

Masdar, Anita Dewi, Sabri Haris, and Astuti Masdar. “Perilaku Struktural Sambungan Sekrup Searah Dan Berlawanan Arah Pada Struktur Baja Ringan.” SIGMA TEKNIKA 4, no. 2 (2021): 271-276.

Nindyawati, Nindyawati, Gede Agung Shri Parta, Adjib Karjanto, and Wahyo Hendarto Yoh. “EKSPERIMENTAL MOMEN-LENDUTAN BALOK KANTILEVER BAJA CANAI DINGIN DENGAN VARIASI JUMLAH SEKRUP.” BANGUNAN 27, no. 2 (2022): 7-16.

SAMBUANTARA, WAYAN YOGA. “Pengaruh Jarak Sekrup Dan Tepi Ujung Sambungan Baja Ringan Profil C Terhadap Kuat Bending.” PhD diss., Universitas Tadulako, 2023.

PANGARIBUAN, ROY F. "ANALISIS KUAT BENDING PADA BAJA RINGAN PROFIL C MENGGUNAKAN PAKU KELING." PhD diss., Universitas Tadulako, 2020.

Riezki, Nanda Noer. "Analisa Kekuatan Sambungan Pada Plat Tipis Dengan Menggunakan Paku Keling." PhD diss., 2017.

RIFAI, MUHAMMAD. "Analisis Kekuatan Tarik Pada Sambungan Baja Ringan Menggunakan Paku Keling." PhD diss., Universitas Tadulako, 2019.

Dwinata, Brilliant, Adi Ganda Putra, and Fauziyya Hafizha Riana. "Analisa Kekuatan Sambungan Rivet Zig-Zag dan Inline dengan Plat AL 2024-T3." Syntax Idea 3, no. 7 (2021): 1551-1564.

NASIONAL, DEPARTEMEN PENDIDIKAN. "MEMBUAT MACAM-MACAM SAMBUNGAN PELAT."

Jati, Dinar Gumilang. "EFEKTIVITAS SAMBUNGAN SEBIDANG PADA BATANG TARIK BAJA RINGAN DENGAN PROFIL KANAL." (2018).

MAKING, MARIA YM. "PENGARUH JARAK SEKRUP TERHADAP KAPASITAS LENTUR PENAMPANG TERSUSUN BOX (Closed Section) BAJA CANAI DINGIN." PhD diss., Universitas Gadjah Mada, 2020.

Abadi, Kusuma Putri Wahyu. "Pengaruh Variasi Jenis Alat Sambung Terhadap Beban Lateral Maksimum dan Kekakuan Akibat Beban Siklik (Quasi-Statis) pada Portal Baja Canai Dingin." PhD diss., Universitas Brawijaya, 2020.

Piousan, Soulika. "STUDI EKSPERIMENTAL SAMBUNGAN 4 SEKRUP SEJAJAR-PARALEL DENGAN PEMASANGAN SEARAH DAN BERLAWANAN ARAH PADA KONSTRUKSI BAJA RINGAN." PhD diss., Universitas Andalas, 2019.

DOI: http://dx.doi.org/10.36055/fondasi.v13i2.28646