Vol 11, No 1 (2025)

April 2025

This issue consists of 17 articles by 62 authors from 18 institutions in 3 countries (Indonesia, Nigeria, and Cameroon)

Table of Contents

Articles

Unsafe work practices and work-related stress in motorcycle repair shops: A cross-sectional analysis
Fikrihadi Kurnia, I Made Suartika
PDF
1-8
Optimizing centrifugal water pump design for enhanced water use efficiency in Batam Marina Plantations
Citra Indah Asmarawati, Sadiq Ardo Wibowo, Reno Reza Gumilang
PDF
9-16
Analysis of pipe material classification using the MUSIC-3D method in the oil and gas industry
Erwin Shafira Winoto, Nabila Noor Qisthani
PDF
17-24
Enhancing engineering student retention at Indonesian private university through improved interpersonal interactions and social integration
Yulianti Talar, Jimmy Gozaly, Grace Vania
PDF
25-33
Research trends on business strategy formulation: A systematic literature review and bibliometric analysis
Arif Rahman, Triwulandari Satitidjati Dewayana, Rahmi Maulidya, Willy Arafah
PDF
34-42
Development of an Android-based quality detection system for young coconut with ADDIE and ISD
Wahyudin Wahyudin, Dene Herwanto, Firda Ainun Nisah, Billy Nugraha, Taufik Nur Wahid, Wahyu Fitrianto
PDF
43-57
Optimal location selection for a new processing plant using supply chain and distribution network analysis
Adekunle Ibrahim Musa
PDF
58-63
Determination of stock in inbound logistics based on optimal order quantity through Smart Application for Chicken Egg Stock (SAFCES)
Agung Prayudha Hidayat, Sesar Husen Santosa, Ridwan Siskandar, Derry Dardanella, Putro Ferro Ferdinant
PDF
64-72
Integration of SERVQUAL and Six Sigma for enhancing academic service quality in departments and laboratories: A case study
Maria Ulfah, Faula Arina, Atia Sonda, Yusraini Muharni, Shanti Kirana Anggraeni, Akbar Gunawan, Ade Irman S. Muttaqin
PDF
73-84
Assessing university service quality and student satisfaction using PLS-SEM
Sarah Isniah, Ade Supriatna, Gita Prawesti, Hidayat Dhuha
PDF
85-94
Analysis of mental workload during exams in hybrid learning in the new normal era post-pandemic
Yayan Harry Yadi, Ani Umyati, Ade Sri Mariawati, Lovely Lady, Nustin Merdiana Dewantari, Lely Herlina, Rezi Alvizar
PDF
95-102
Optimization of compressive strength for Aceh Besar traditional bricks using Box-Behnken design
Riski Arifin, Sri Rahmawati, Sitti Annisa
PDF
103-112
A regression-based model of MSME strategy effectiveness during and beyond the COVID-19 crisis
Dyah Lintang Trenggonowati, Putiri Bhuana Katili, Moses Laksono Singgih, Asep Ridwan
PDF
113-124
Analysis of the modernity, effectiveness and safety of two industrial cutting machines
Tsapi T Kevin, Soh Fotsing B. Desire, Bienvenu Kenmeugne
PDF
125-135
Strengthening screw shaft measurement system in teaching factory through measurement system analysis: A case study
Fredy Sumasto, Bayu Samudra, Ali Rachman Hakim, Febriza Imansuri, Indra Rizki Pratama
PDF
136-149
Halal control point (HCP) analysis in the raw material supply chain using the failure mode effect and criticality analysis (FMECA) method
Akhmad Sadeli, Khafizh Rosyidi
PDF
150-158
Safety improvement through root cause analysis and hazard control in lift installation
Valentino Bernardus Gurning, Dian Mardi Safitri
PDF
159-166